Personal menu

Manufacturer:

FOSROC PROOFEX CAVITYDRAIN 80 (2.07mX20m)

Fosroc Cavitydrain membranes are manufactured from chemically resistant high density polyethylene in a range of stud depths designed to permit high water flow through a permanent void formed against a substrate. Fosroc Proofex Cavitydrain 80 is a space saving solution for vertical applications in conjunction with internal blockwork walls and dry lining systems. Unit Size: 2.07m x 20m

Availability: Out of stock

Depot Stock

Bury St Edmunds Depot	Out of stock
Kent Depot	Out of stock
Midlands Depot	Out of stock
Sheffield Depot	3 in stock
West London Depot	Out of stock

£250.38 excl tax

Qty:

i h

Overview
Downloads
Product Disclaimer
Contact Us

Advantages:
◇ Suitable for new and existing construction
◇ Acceptable for all water table classifications (low, variable, high) as per Table 1 of BS8102-2009
◇ Elimnates increase in structural load due to water pressure
◇ Provides a maintainable form of ingress protection
◇ Can be specified in conjunction with a monitoring system to provide automatic alerts in the event of pump failure
◇ Internal applcation in a controlled environment reduces risk of defective installation
◇ Provides a continuous drainage pathway and vapour barrier
◇ Minimal deformation under load maintains drainage performance
◇ Conical voids enable high load transfer to structural elements
◇ Chemically resistant, unaffected by contaminated substrates and chemicals typically found in groundwater
◇ Vertical and horizontal grades available

Technical Datasheet

The product image(s) shown are for illustration purposes only and may not be an exact representation of the product.

The recommendations relating to the application and end-use of the products mentioned are based on our current knowledge and experience of the products when properly stored, handled and applied under normal conditions. All product specification, information and data made available on the website is subject to change. All information presented is believed to be accurate and reliable, but is given without guarantee, warranty or responsibility of any kind.

Your name *

Your email *

Subject: *

Enquiry *

Products from the Same Manufacturer

FOSROC CONBEXTRA GP GROUT 25 KILO B

Fosroc Conbextra GP Grout is a high-flow, nonshrink cementitious grout, conforming to the requirements of BS EN 1504-3 Class R4 and BS EN 1504-6: Anchoring of a reinforcing steel bar. Used for grouting gap thicknesses 10 to 75mm. Unit Size: 25kg

Stock Status: 720 in stock

£11.51 excl tax

FOSROC GX GUN 600cc (FOR FOILED PRODUCTS - SAUSAGES)

(FOR FOILED PRODUCTS - SAUSAGES)

Stock Status: 35 in stock

£65.17 excl tax

FOSROC LOKFIX E35S 300ml CARTRIDGE

Fosroc Lokfix E35S is a two component polyester anchoring material, supplied in single component cartridges with a static mixer nozzle. When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates. Unit Size: 300ml

Stock Status: Out of stock

£276.20 excl tax

FOSROC LOKFIX E55S 300ml CARTRIDGE

Fosroc Lokfix E55S is a two component vinyl-ester anchoring material, supplied in single component cartridges with a static mixer nozzle. When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates. Unit Size: 300ml

Stock Status: Out of stock

£293.15 excl tax

FOSROC LOKFIX E75 APPLICATOR GUN

Applicator gun for Lokfix E75 Unit Size: Each

Stock Status: Out of stock

£58.74 excl tax

FOSROC LOKFIX E77 585ml CARTRIDGE (sold by cartridge)

A two-component epoxy anchoring material, supplied in 3:1 ratio side-by-side cartridges with a static mixer nozzle. When applied it sets and cures to firmly secure a variety of steel fixings into concrete and solid masonry substrates. Unit Size: 385ml

Stock Status: Out of stock

£30.89 excl tax

FOSROC LOKFIX S25 2.5Ltr BLUE LID

A two component polyester anchoring grout supplied in pre-measured quantities. The material cures quickly to give consistent, high performance anchorages. It is a pourable grade, with a 25 minute gel time at 20°c for use in vertical down holes where the hole is 8 to 40mm greater in diameter than the bar. Unit Size: 2.5ltr

Stock Status: Out of stock

£66.38 excl tax

FOSROC MS300 SEALANT 600cc

A one part, high modulus sealant based on hybrid silyl modified polyether technology. It has a rapid rate of cure and forms a tough elastomer capable of supporting heavy wheel loads. It may be applied between 6mm and 20mm wide, for internal trafficked flush joints and up to 40mm wide, for non-tracked/recessed tracked joints. Unit Size: 600ml

Stock Status: 932 in stock

£11.45 excl tax

FOSROC MS60 SEALANT GREY 380CC

A one part, low modulus sealant based on hybrid silyl modified polyether technology. It is suitable for sealing joints in concrete, brickwork, blockwork, perimeter sealing around doors and windows, and non-trafficked floor joints. Unit Size: 380ml

Stock Status: Out of stock

£11.34 excl tax

FOSROC MULSEAL DP 25LTR

A single part bitumen latex emulsion, applied by brush or squeegee. The incorporation of rubber latex imparts elasticity to the dried coating. Mulseal DP is suitable for use on most building materials such as concrete, brickwork, metals and stone. Unit Size: 25ltr

Stock Status: Out of stock

£142.68 excl tax

FOSROC PROOFEX CAVITYDRAIN 80 (2.07mX20m)

Payment options