Personal menu

Manufacturer:

FOSROC LOKFIX E77 440ml CARTRIDGE (sold by cartridge)

A two-component epoxy anchoring material, supplied in 3:1 ratio side-by-side cartridges with a static mixer nozzle. When applied it sets and cures to firmly secure a variety of steel fixings into concrete and solid masonry substrates. Unit Size: 385ml

Availability: Out of stock

Depot Stock

Bury St Edmunds Depot	Out of stock
Kent Depot	Out of stock
Midlands Depot	Out of stock
Sheffield Depot	Out of stock
West London Depot	Out of stock

£36.76 excl tax

Qty:

i h

Overview
Specifications
Downloads
Product Disclaimer
Contact Us

Uses:
◇ For concrete (solid, porous and light), masonry and hollow bricks.
◇ Accredited for use in dry, damp and flooded concrete substrates.
◇ Can be used with cracked concrete
◇ Fixing of post installed reinforcement
◇ Anchoring of threaded rod fixings
◇ Anchoring of internal threaded rod sleeves
◇ Internal, external and submerged conditions
◇ Can be applied to almost any size of fixing
◇ For horizontal, vertical and overhead application.
◇ Bonding and surface crack sealing applications.

Advantages:
◇ High bond strengths for heavyweight fixings or economical design
◇ High durability: Tested to achieve 100 year design life
◇ No additional mixing equipment required
◇ Does not apply expansive force to the substrate
◇ Fixings can be spaced closer together than mechanical anchors
◇ Enables fixings closer to edges than mechanical anchors
◇ Re-usable by replacing sealing cap, product may be kept to the end of original shelf life
◇ Low VOC
◇ Tested with diamond drilled bore holes
◇ Waterproof, protecting the embedded fixing from corrosion and water penetration into the substrate
◇ Extended gel times allow for more complex procedures
◇ Fire rated up to 2 hours (consult test data for specific conditions)
◇ 24 month shelf life

Products specifications

Shelf Life	Lokfix E77 Cartridges have a maximum shelf life of 24 months when kept in a dry warehouse at between +5 to +35ºC. It is possible to allow cartridge temperature to raise to +40ºC immediately prior to application.

Technical Datasheet

The product image(s) shown are for illustration purposes only and may not be an exact representation of the product.

The recommendations relating to the application and end-use of the products mentioned are based on our current knowledge and experience of the products when properly stored, handled and applied under normal conditions. All product specification, information and data made available on the website is subject to change. All information presented is believed to be accurate and reliable, but is given without guarantee, warranty or responsibility of any kind.

Your name *

Your email *

Subject: *

Enquiry *

Products from the Same Manufacturer

FOSROC CONBEXTRA GP GROUT 25 KILO B

Fosroc Conbextra GP Grout is a high-flow, nonshrink cementitious grout, conforming to the requirements of BS EN 1504-3 Class R4 and BS EN 1504-6: Anchoring of a reinforcing steel bar. Used for grouting gap thicknesses 10 to 75mm. Unit Size: 25kg

Stock Status: 2395 in stock

£14.42 excl tax

FOSROC GX GUN 600cc (FOR FOILED PRODUCTS - SAUSAGES)

(FOR FOILED PRODUCTS - SAUSAGES)

Stock Status: 56 in stock

£82.35 excl tax

FOSROC LOKFIX E35S 300ml CARTRIDGE

Fosroc Lokfix E35S is a two component polyester anchoring material, supplied in single component cartridges with a static mixer nozzle. When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates. Unit Size: 300ml

Stock Status: Out of stock

£336.22 excl tax

FOSROC LOKFIX E55S 300ml CARTRIDGE

Fosroc Lokfix E55S is a two component vinyl-ester anchoring material, supplied in single component cartridges with a static mixer nozzle. When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates. Unit Size: 300ml

Stock Status: Out of stock

£34.72 excl tax

FOSROC LOKFIX E75 APPLICATOR GUN

Applicator gun for Lokfix E75 Unit Size: Each

Stock Status: Out of stock

£74.22 excl tax

FOSROC LOKFIX S25 2.5Ltr BLUE LID

A two component polyester anchoring grout supplied in pre-measured quantities. The material cures quickly to give consistent, high performance anchorages. It is a pourable grade, with a 25 minute gel time at 20°c for use in vertical down holes where the hole is 8 to 40mm greater in diameter than the bar. Unit Size: 2.5ltr

Stock Status: Out of stock

£80.80 excl tax

FOSROC MS300 SEALANT 600cc

A one part, high modulus sealant based on hybrid silyl modified polyether technology. It has a rapid rate of cure and forms a tough elastomer capable of supporting heavy wheel loads. It may be applied between 6mm and 20mm wide, for internal trafficked flush joints and up to 40mm wide, for non-tracked/recessed tracked joints. Unit Size: 600ml

Stock Status: 256 in stock

£14.48 excl tax

FOSROC MS60 SEALANT GREY 380CC

A one part, low modulus sealant based on hybrid silyl modified polyether technology. It is suitable for sealing joints in concrete, brickwork, blockwork, perimeter sealing around doors and windows, and non-trafficked floor joints. Unit Size: 380ml

Stock Status: Out of stock

£13.40 excl tax

FOSROC MULSEAL DP 25LTR

A single part bitumen latex emulsion, applied by brush or squeegee. The incorporation of rubber latex imparts elasticity to the dried coating. Mulseal DP is suitable for use on most building materials such as concrete, brickwork, metals and stone. Unit Size: 25ltr

Stock Status: Out of stock

£180.27 excl tax

FOSROC NITOBOND AR 5LTR

A modified acrylic emulsion which is specially designed for use as a bonding aid, curing agent and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external application. Unit Size: 5ltr

Stock Status: 54 in stock

£142.25 excl tax

FOSROC LOKFIX E77 440ml CARTRIDGE (sold by cartridge)

Payment options