Personal menu

Manufacturer:

25mm FOSROC HYDROCEL 2mX1m

Fosroc Hydrocell XL is a cross linked, semi-rigid, closed cell polyethylene sheet material used for forming or filling expansion joints between adjacent in-situ or precast components.

Hydrocell XL provides excellent support back to elastomeric sealants and is especially recommended for use in expansion joints in brickwork and in the construction of water retaining and water excluding structures.

Unit Size: 25mm x 1000mm x 2000mm

Availability: 157 in stock

Depot Stock

Bury St Edmunds Depot	56 in stock
Kent Depot	Out of stock
Midlands Depot	32 in stock
Sheffield Depot	33 in stock
West London Depot	36 in stock

£83.86 excl tax

Sold in units of: SHEET

Qty:

i h

Overview
Specifications
Product Disclaimer
Downloads
Contact Us

Uses:
◇ Potable water reservoirs
◇ Culverts and canals
◇ Sewage tanks
◇ Roadways and hardstandings
◇ Retaining walls
◇ Basement structures and subways
◇ Runways, taxiways and aprons

Advantages:
◇ Cross linked to resist lateral and hydrostatic pressure
◇ High density support of sealant to prevent adhesion failure
◇ Non-absorbent closed cell structure
◇ High-compression recovery
◇ Non-extruding
◇ Low load transfer to joint edges
◇ Non-tainting and rot proof
◇ Chemically resistant
◇ Bitumen free
◇ Natural bond breaker

Products specifications

Unit Sizes Available	Hydrocell XL is supplied in the following sheet sizes and can be easily cut to the required size with a Stanley knife or saw. 10 mm x 1000 mm x 2000 mm, 15 mm x 1000 mm x 2000 mm, 20 mm x 1000 mm x 2000 mm, 25 mm x 1000 mm x 2000 mm
Shelf Life	Hydrocell XL should be stored in original unopened packaging, in cool dry conditions, away from sunlight.

The product image(s) shown are for illustration purposes only and may not be an exact representation of the product.

The recommendations relating to the application and end-use of the products mentioned are based on our current knowledge and experience of the products when properly stored, handled and applied under normal conditions. All product specification, information and data made available on the website is subject to change. All information presented is believed to be accurate and reliable, but is given without guarantee, warranty or responsibility of any kind.

Technical Datasheet

Your name *

Your email *

Subject: *

Enquiry *

Products from the Same Manufacturer

FOSROC CONBEXTRA GP GROUT 25 KILO B

Fosroc Conbextra GP Grout is a high-flow, nonshrink cementitious grout, conforming to the requirements of BS EN 1504-3 Class R4 and BS EN 1504-6: Anchoring of a reinforcing steel bar.

Used for grouting gap thicknesses 10 to 75mm.

Unit Size: 25kg

Stock Status: 1068 in stock

£11.51 excl tax

FOSROC GX GUN 600cc (FOR FOILED PRODUCTS - SAUSAGES)

(FOR FOILED PRODUCTS - SAUSAGES)

Stock Status: 48 in stock

£65.17 excl tax

FOSROC LOKFIX E35S 300ml CARTRIDGE

Fosroc Lokfix E35S is a two component polyester anchoring material, supplied in single component cartridges with a static mixer nozzle.
When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates.

Unit Size: 300ml

Stock Status: Out of stock

£276.20 excl tax

FOSROC LOKFIX E55S 300ml CARTRIDGE

Fosroc Lokfix E55S is a two component vinyl-ester anchoring material, supplied in single component cartridges with a static mixer nozzle.
When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates.

Unit Size: 300ml

Stock Status: Out of stock

£293.15 excl tax

FOSROC LOKFIX E75 APPLICATOR GUN

Applicator gun for Lokfix E75 Unit Size: Each

Stock Status: Out of stock

£58.74 excl tax

FOSROC LOKFIX E77 585ml CARTRIDGE (sold by cartridge)

Fosroc Lokfix E77 is a two-component epoxy anchoring material, supplied in 3:1 ratio side-by-side cartridges with a static mixer nozzle. When applied it sets and cures to firmly secure a variety of steel fixings into concrete and solid masonry substrates. Unit Size: 385ml

Stock Status: 41 in stock

£30.89 excl tax

FOSROC LOKFIX S25 2.5Ltr BLUE LID

Fosroc Lokfix S25 is a two component polyester anchoring grout supplied in pre-measured quantities.

The material cures quickly to give consistent, high performance anchorages.

It is a pourable grade, with a 25 minute gel time at 20°c for use in vertical down holes where the hole is 8 to 40mm greater in diameter than the bar.

Unit Size: 2.5ltr

Stock Status: Out of stock

£66.38 excl tax

FOSROC MS300 SEALANT 600cc

Fosroc Nitoseal MS300 is a one part, high modulus sealant based on hybrid silyl modified polyether technology.
It has a rapid rate of cure and forms a tough elastomer capable of supporting heavy wheel loads.
It may be applied between 6mm and 20mm wide, for internal trafficked flush joints and up to 40mm wide, for non-tracked/recessed tracked joints.

Unit Size: 600ml

Stock Status: 1121 in stock

£11.45 excl tax

FOSROC MS60 SEALANT GREY 380CC

Fosroc Nitoseal MS60 is a one part, low modulus sealant based on hybrid silyl modified polyether technology.
It is suitable for sealing joints in concrete, brickwork, blockwork, perimeter sealing around doors and windows, and non-trafficked floor joints.

Unit Size: 380ml

Stock Status: Out of stock

£11.34 excl tax

FOSROC MULSEAL DP 25LTR

Fosroc Mulseal DP is a single part bitumen latex emulsion, applied by brush or squeegee.
The incorporation of rubber latex imparts elasticity to the dried coating.
Mulseal DP is suitable for use on most building materials such as concrete, brickwork, metals and stone.

Unit Size: 25ltr

Stock Status: Out of stock

£142.68 excl tax

25mm FOSROC HYDROCEL 2mX1m

Payment options