Waterproofing

The Sika Bentoshield Fixing Nose Piece is designed to support the washer on the end of the gun and hold it in place for safe and correct fixing of the Sika Bentoshield membrane system. Unit Size:

A 2 component polymer modified bituminous flexible thick coating extended with fibre for waterproofing against dampness and moisture ingress. Unit Size: 32kg (Part A-Liquid=24kg, Part B-Powder=8kg)

A flexible 0.6mm composite damp proof course and cavity tray system. It is supplied in 20m rolls and available in a wide-variety of widths. Unit Size: 225mm x 20m roll

Visqueen High Performance Urban Drainage Geomembrane is a robust thermoplastic geomembrane, black in colour, 1mm thick and supplied in single wound rolls (not folded). Unit Size: 1.4m x 50m

Drainage and protection cavity membrane used externally against retaining walls and across terraces and podiums. Unit Size: 2m x 15m x 7mm roll

A geocomposite drainage sheet with a 8mm thick HDPE cuspated core and non-woven polypropylene geotextiles, recommended for most building and civil engineering drainage applications. Unit Size: 2.4m x 20m roll

Masterlife WP 754 is a pre-applied sheet membrane waterproofing system consisting of highly flexible polyolefin membrane and a designed non-woven fleece. Unit Size: 1.6MM X 1.0M X 20M

Masterlife WP 754 is a post-applied sheet membrane waterproofing system consisting of a highly flexible polyolefin membrane with self adhesive backing. Unit Size: 1m x 20m

Hyload Gastite is a cold applied self-adhesive membrane protecting structures against the ingress of moisture and methane radon gasses.

Unit Size: 1m x 20m rolls

Cetco Aquadrain ICD 20mm is the highest drainage capacity membrane in the Aquadrain ICD range giving a void volume of 14 litres/m². Unit Size: 2.0m x 20m* *including flat overlapping edge (flange) without studs, working area ca. 40m²

RIW Cavity Drain R7 is manufactured from 0.5mm translucent virgin high density polyethylene with studs approximately 8mm high. Unit Size: 2m wide x 20m long

GCP Betec Mesh is a reinforcing mesh for use where substreate cracking has or is likely to occur.

A two component, solvent free, highly elastic, low odour polyurea hybrid waterproofing membrane. Unit Size: 25kg (Part A= 9.2kg, Part B=15.8kg)

A flexible waterproofing tape based on modified flexible Polyolefin (FPO) with advanced adhesion properties. It has red masking tape on one side for easier application over expansion joits. Unit Size: 1 roll of 25m length Varying widths available: 10, 20, 30cm

A 1.0mm thick high density polyethylene (HDPE) profiled sheet with approximate 20 mm high studs . Unit Size: 2m x 20m roll

An economical low capacity, low friction bearing strip which can be used under in-situ or precast concrete slabs and beams, structural steelwork bearing plates and pipe support to form a thin sliding joint.

Unit Size: Roll

Minova CarboStop 102 is a water-reactive, CFC and solvent free, one-component polyurethane resin.

It is an easy to use way of stopping water inflow under high pressure.

Unit Size: Kit - consists of part A (102 20kg tin) & B (102 Acc 1kg tin)

A galvanised metal sheet with a special coating applied on one side to increase its adhesion to fresh concrete Unit Size: 15m rolls

JUTA GP Titanbond Edge Strip is a specially designed narrow width roll of the GP Titanbond for use on kicker details, or transitions areas from horizontal to vertical. Unit Size: 1m x 25m

A crystalline waterproofing admixture powder consisting of a blend of specially selected chemicals. When combined with ready mix concrete at batching plant, it produces a crystalline reaction which enhances water resistance and durability of the cured concrete. Unit Size: A tub consisting of six 4.1 kg soluble bags and used in the ratio of 1:1 i.e. one 4.1kg bag for each 1m³ of concrete.

Triton Platon P20 Cavity Drain is a high capacity drainage membrane recommended for use on all floor applications below ground due to its ability to control free flowing water. Unit Size: 2m x 20m x 20mm roll

A two component system both supplied in the same tin. The first component (Part A) is a bitumen-extended polyurethane fluid (15kg). The second component (Part B) is an accelerator hardener (0.6kg). Unit Size: 15.6kg

GCP Serviseal AT 240 is an important advance in concrete joint protection which combines Active Technology with the conventional mechancial properties of PVC waterstops, developed for water exclusing and retaining structures such as basements, reservoirs, sewage treatment works etc. Unit Size: 7.5 m long coil

.

A high density polyethylene (HDPE), heavy duty drainage and protection sheet with 10mm high dimples on the bottom layer and a bonded geotextile (PP) filtration layer on the top layer. Unit Size: 2,44m width x 12,50m length

A two-pack solvent free black liquid modified epoxide surface conditioner that can be applied to damp surfaces. Unit Size: 5ltr or 15 ltr (2-part)

A flexible 0.6mm composite damp proof course and cavity tray system. It is supplied in 20m rolls and available in a wide-variety of widths. Unit Size: 300mm x 20m roll

An acrylic sealing ring profile. It swells in contact with water to seal spacer bars / tie bars / tie rods. Unit Size: Internal Diameter=18mm, External diameter=20mm

GCP Hydroduct CF is a high density polyethylene combined cavity former and vapour barriers for drained BS 8102:2009 Type C basement construction. Hydroduct CF 20 is used for forming drained cavities horizontally and vertically. Hydroduct CF 08 is used for forming drained cavities horizontally and vertically in lower risk applications. Unit Size: Hydroduct CF 20: 2m x 20m roll Hydroduct CF 08: 2.4m x 20m roll

A cold applied, high density polyethylene film bonded to aluminium foil and coated with bitumen/rubber self adhesive layer with a removable reinforced silicone release paper. Unit Size: 1m x 20m long

.

Cetco Hydrofix 600 is a single part, rapid curing, modified polyurethane waterproofing membrane that can be applied directly to dry concrete surfaces. Unit Size: 15ltr drum

A grey, single component liquid damp proof and waterproof membrane. Unit Size: 20kg tins

Ardex DPM 1 C can be applied to protect the floor covering installation from residual construction moisture and ground bearing moisture. Unit Size: 25kg

A polyolefin (FPO) based sheet membrane for below waterproofing of reinforced concrete structures. Unit Size: 1m x 25m roll

An acrylic sealing ring profile. It swells in contact with water to seal spacer bars / tie bars / tie rods. Unit Size: Internal Diameter=43mm, External diameter=45mm

GCP Hydroduct CF is a high density polyethylene combined cavity former and vapour barriers for drained BS 8102:2009 Type C basement construction. Hydroduct CF 20 is used for forming drained cavities horizontally and vertically. Unit Size: 2m x 20m roll This product is not purchasable on the website. Please call or email to place your order.

.

An acrylic sealing ring profile. It swells in contact with water to seal spacer bars / tie bars / tie rods. Unit Size: Internal Diameter=26mm, External diameter=28mm

A BBA approved high performance, totally gas-impervious, reinforced membrane. It is a black/white, multi-layer, low density polyethylene, ground gas resistant based membrane with an integral aluminium foil layer and a polypropylene reinforcing grid. Unit Size: 2m x 50m roll This product is not purchasable on the website. Please call or email to place your order.

RIW R20 Cavity Drain is manufactured from 1mm thick black high density polyethylene with studs approximately 20mm high. Unit Size: 2m wide x 20m long

A two pack solvent free polymer modified epoxide coating which cures to give a continuous tough but flexible waterproof coating. Unit Size: 20kg (2-part)

A cold applied combination of impermeable high density polyethylene sheet and permeable geotextile filter fabric. Unit Size: 2m x 20m long rolls This product is not purchasable on the website. Please call or email to place your order.

GCP Slipstrip 2 is low capacity bearing slips made from dense extruded polyethylene sheet for fixed end rotation joints or as a low friction, structural slip membrane. Unit Size: 300mm wide, 1.5mmn thick x 25m rolls

Adocoat is an alkali resistant cold applied rubberised bitumen emulsion which imparts excellent adhesion to sound building materials, including asphalt. Unit Size: 205ltr

An embossed polyolefin FPO sheet membrane for pre-applied fully bonded below ground waterproofing of reinforced concrete structures. Unit Sizes: 1m x 25m