Waterproofing

A trowel-grade, sodium bentonite/butyl-rubber based sealant, designed for use with the Structureseal system. Unit Size: 15 ltr tub

A modifed bitumen rubber membrane with a self adhesive coating protected by a removable polyethylene release flm. It is dark grey on the upper surface. Unit Size: 1m x 20m roll

A cold applied, flexible, high performance waterproofing and radon barrier membrane, incorporating a cross laminated HDPE carrier film with a polymer modified bitumen compound. Unit Size: 1m x 20m

A cold applied, bitumen based coating, which dries to form a uniform UV resistant and waterproof layer. The coating is a fibre and mineral filled solution of natural and petroleum bitumens in white spirit. Unit Size: 20 ltr

A flexible 0.6mm composite damp proof course and cavity tray system. It is supplied in 20m rolls and available in a wide-variety of widths. Unit Size: 150mm x 20m roll

.

Swellable hydrophilic polymer waterstops. Manufactured from thermoplastic synthetic rubber, the products are lightweight and highly flexible. Unit Sizes: IGW5 Waterstop = 10m long strips, 20mm wide and 5mm high.

A 150mm wide tape which has many uses but is mostly used to seal membrane from walls to floors and the channel system. Tacky on one side only, this can also be used to overtape external joints and used on floor oversealing. Unit Size: 150mm x 20m

Ardex DPM 1 C can be applied to protect the floor covering installation from residual construction moisture and ground bearing moisture. Unit Size: 10kg

.

.

A glass fibre mat reinforcement for Decothane and Sikalastic Liquid Applied Membrane Systems. Unit Size: Roll

A single component mastic consisting of polymer modified natural sodium bentonite and further polymer additives. Trowel applied and thixotropic in nature. Unit Size: 15ltr

GCP Bituthene Primer S2 is a rubber-based primer in solvent, specially formulated to provide good initial adhesion, for use with the Bituthene range of cold applied, self adhesive waterproof membranes. Unit Size: 25 ltr can

Flexcrete Cemprotec Elastic is an elastomeric, cementitious modified, polymer-rich coating which maintains its flexibility under permanent immersion and when exposed externally.

Unit Size: 30kg

Ardex WPM 200 provides a surface applied water and vapour barrier or priming layer to concrete, screeded, rendered or masonry surfaces, steel and other vertical as well as horizontal hard surfaces. Unit Size: 5ltr

Ardex WPM 200 provides a surface applied water and vapour barrier or priming layer to concrete, screeded, rendered or masonry surfaces, steel and other vertical as well as horizontal hard surfaces. Unit Size: 5ltr

Sika Bentoshield fixing washers are special plastic washers used to fix Sika Bentoshield membrane to vertical surfaces and horizontal laps. Unit Size:

A 0.5mm thick high density polyethylene (HDPE) profiled sheet with approximate 7 mm high studs. Unit Size: roll of 2.07m x 20m with a 70mm flange edge on one side to aid jointing

Sika® Brick plugs are 10mm fixings to use with membrane systems, with the advantage of a rubber seal already attached. Unit Size: 200 per box

A rectangular acrylic sealing profile. It swells in contact with water to seal all types of construction joints and penetrations in concrete structures. Unit Size: 20mm x 5mm x 20m

A high performance epoxy waterproof resin for detailing of waterproofing and ground gas protection systems. It is a three component system consisting of base resin, liquid hardener and specially graded inert fillers. It is suitable for thicknesses from 20-100mm. Unit Size: 15 ltr packs containing liquid, base and hardener.

Wykamol CM20 is a high capacity waterproofing membrane

Unit Size: 2mx20m roll

Fosroc Cavitydrain membranes are manufactured from chemically resistant high density polyethylene in a range of stud depths designed to permit high water flow through a permanent void formed against a substrate. Fosroc Proofex Cavitydrain 80 is a space saving solution for vertical applications in conjunction with internal blockwork walls and dry lining systems. Unit Size: 2.07m x 20m

A high performance methane, radon and carbon dioxide resisting, self-adhesive waterproof membrane for basements and below ground structures. It incorporates an aluminium layer and a polymer modified bitumen compound on a high strength polymer backing film. Unit Size: 1m x 20m

Visqueen Ultimate Gas DPC utilises Visqueen's Advanced Barrier Technology. The DPC is a 0.5mm thick, flexible 7 layer co-extruded film providing volatile organic compound (VOC) and ground gas resistance. The DPC has an embossed/debossed fnish, is coloured gold/white and can be installed with either surface facing upwards. Unit Size: 900mm X 20m roll

A fully bonded, composite sheet membrane waterproofing system for reinforced concrete structures. It consists of an embossed polyolefin (FPO) based membrane laminated with a unique sealant and a non-woven fleece with a self-adhesive strip on the longitudinal side for the overlap. Unit Sizes: 1m x 30m

Fosroc Supercast Rearguard sections incorporate a flat top center box, allowing movement to be accommodated in expansion joints. They also provide a seat to support joint fillers. Unit Size: 200mm x 12m Roll

A self‐adhesive tape, based on a polyacrylate adhesive on a yellow carrier film coated with the SikaProof A fully bonded system. Unit Sizes: 150mm x 25m roll

An advanced, elastomeric, highly tear resistant, breathable, waterproof composite tape. Unit Size: 120mm wide x 10m long roll

Visqueen Gas Resistant Self Adhesive Membrane is a foil lined modifed bitumen rubber membrane with a self adhesive coating protected by a removable polyethylene release flm. Unit Size: 1m x 20m

Visqueen Ultimate Gas DPC utilises Visqueen's Advanced Barrier Technology. The DPC is a 0.5mm thick, flexible 7 layer co-extruded film providing volatile organic compound (VOC) and ground gas resistance. Unit Size: 850mm x 20m

A two-component, fast-setting, flexible and tough epoxy system. Unit Size: 6 x 560ml sachet units (includes 3 static mixers)

Juta GP Titantech DPC is a unique single layer, embossed high performance, gas and hydrocarbon resistant DPC. Unit Size: 1.3m x 20m

A single-sided, self-adhesive tape based on SikaProof® membrane, laminated with a butyl adhesive covered with a release liner. Unit Size: 200mm x 20m

A solvent free polymer modified epoxide coating, supplied as a two part pack of base and hardener in pre-measured proportions. Unit Sizes: 5ltr & 20ltr packs (two part product) Grey or Black

A solvent free polymer modified epoxide coating, supplied as a two part pack of base and hardener in pre-measured proportions. Unit Sizes: 5ltr

A high performance polymeric material, available in widths from 100mm to 1000mm, supplied in rolls 20m long. Unit Size: Length 20m long rolls Widths (various available) 100,150, 225, 300, 375, 450, 600, & 1000mm

Cetco Ultraseal XP is an active waterproofing membrane for exceptional performance in a wide-range of contaminated environments. Unit Size: 1.15m x 8.7m (10m²) roll

BASF Masterseal 930 is a joint waterproofing bandage and epoxy resin adhesive. Unit Size: 200 x 1mm x 20m

MasterLife WP 754 PC Tape is a double sided butyl tape which is used for Masterseal 754 pre-applied waterproofing applications at critical details and damaged areas. Unit Size: 100mm X 100m

A cold applied, high density polyethylene film, coated with a bitumen/rubber self-adhesive layer with a removable reinforced silicone paper.

Unit Size: 1m x 20m roll

Fosroc Supercast Rearguard sections incorporate a flat top center box, allowing movement to be accommodated in expansion joints. They also provide a seat to support joint fillers. Unit Size: 250mm x 12m Roll

A high-density polyethylene, high capacity cavity drainage membrane. Unit Size: 2m x 20m long

GCP Bituthene 8000 is an advanced, self-adhesive membrane with unique HDPE composite film that provides superior physical properties for water and vapour proof application in sub-structures. Unit Size: 1m x 20m roll

Juta GP Titantank is a self adhesive version of the GP Titanflex; composed of self-adhesive with an upper surface finish of GP Titanflex, and a lower surface finish of siliconised polypropylene release film. Unit Size: 1.2mm x 0.9m x 20m