Sika

A very low emission cement based self-levelling compound suitable for interior areas, characterised by good working properties. Suitable for castor chair rollers according to EN 12 529. Unit Size: 25kg

A one component cement based polymer modified general purpose repair and reprofiling mortar, meeting the requirements of Class R3 of BS EN 1504-3. Unit Size: 25kg bag

A cement based, one-component, rapid setting, shrinkage compensated repair concrete. Unit Size: 25kg

A fast curing, non-swelling, 1-part adhesive with very high initial grab which bonds most common construction substrates. Can be used for adhering SikasSwell® Profiles within construction joints. Unit Size: 600ml sausage

Trak-It C5 Fuel cells are spare fuel cells to power the Trak-It C5 gas fixing tool. Each fuel cell contains enough gas to install over 800 fasteners. Unit Size: each

An epoxy-based, moisture tolerant, thixotropic, two-part structural adhesive, which bonds most construction materials. Unit Size: 2 part Pack (Part A 0.9kg, Part B 0.3kg)

Sika Screeding Mortar when mixed with water provides the multicoat components for the structural waterproofing systems Unit Size: 25kg bag

Sika®-1 Pre-bag Render Mortar is part of the Sika® 1 Pre-Bagged Structural Waterproofing System. Unit Size: 25kg

Sika 1 Finishing Mortar is part of the Sika 1 Pre-Bagged Structural Waterproofing System. These special mortars are pre-bagged kiln dried blends of specially graded aggregates and cements, with waterproofing admixtures, packaged in 4 grades at the appropriate mix ratios for optimum application performance and durability. Unit Size: 25kg

A drainage outlet that can be used to get water from the channels to the sump chamber or existing drain. The angle bend on the underside of the channel takes water through a 32mm connection.

Sika®-1 Pre-bag Spritz Mortar is part of the Sika® 1 Pre Bagged Structural Waterproofing System. Unit Size: 25kg

A 1-part, cementitious, fibre reinforced, low shrinkage repair mortar. It contains recycled waste materials and can reduce the carbon footprint application activity calculations. Unit Size: 25kg bag

A 1-part, cementitious, polymer modified coating material used as bonding primer and reinforcement corrosion protection. It contains recycled waste materials which leads to a reduced carbon footprint compared to an equivalent performing mortar. Unit Size: 25kg

A rapid setting waterproofing admixture, which when mixed with ordinary Portland cement and water, sets rapidly to seal areas of severe water infiltration through concrete, rock or masonry. Unit Size: 5ltr

A bitumen solution to be used in conjunction with Sika BituSeal S-115. Unit Sizes: 25ltr, 5ltr

A solvent blend used in combination with epoxy or polyurethane based products and membranes. Unit Size: 3ltr

A Portland cement based product giving high strength, good flow and non-shrink properties. Unit Size: 25kg

A one component cement based polymer modified high build repair and reprofiling mortar, meeting the requirements of Class R3 of BS EN1504-3. Unit Size: 25kg bag

An extra-quick setting liquid waterproofing admixture that causes almost immediate setting and very rapid hardening of Ordinary Portland Cement. Unit Size: 5ltr

A 1-part, polymer modified, ready to use bitumen emulsion primer. Unit Size: 10 ltr

Sikaplan 1651 Pipe Penetration Top Hat is a pre-formed collar for 110mm diameter pipe penetrations, compatible with Sikaplan 1651/2/3.

A non-sag, 1-component polyurethane of paste-like consistency for structural joints in ventilated facades and interior wall cladding between the vertically installed substructure and the panel that will be subjected to high dynamic and static stresses. It cures on exposure to atmospheric humidity. Unit Size: 600ml

A thixotropic two part structural adhesive based on epoxy resin in a cartridge Unit Size: 250ml cartridge

The Sika Cavity Drainage System Corner Piece is installed at the corners of a perimeter drainage channel system to allow continuity of the drainage system.

The Sika Cavity Drainage System Channel T Piece is installed at the junction between wall and cross channel drainage system to allow continuity of the drainage system.