Fosroc

A cross linked, semi-rigid, closed cell polyethylene sheet material used for forming or filling expansion joints between adjacent in-situ or precast components. Hydrocell XL provides excellent support back to elastomeric sealants and is especially recommended for use in expansion joints in brickwork and in the construction of water retaining and water excluding structures. Unit Size: 20mm x 1000mm x 2000mm

A two component polyester anchoring grout supplied in pre-measured quantities. The material cures quickly to give consistent, high performance anchorages. It is a pourable grade, with a 25 minute gel time at 20°c for use in vertical down holes where the hole is 8 to 40mm greater in diameter than the bar. Unit Size: 2.5ltr

Fosroc Patchroc 250 is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent repair mortar. Unit Size: 25kg bag

Applicator gun for Lokfix E75 Unit Size: Each

A pre-formed pipe collar with a flat based to simplify pipe penetration details. Available in standard diameters 110mm and 160mm.

A reinforcing mesh for use in conjunction with Proofex LM for angles and pipe penetrations etc. Unit Size: 100mm x 50m

A ready to use, non-shrink, cementitious grout, which has been formulated specifically for grouting of bridge bearings and parapet post baseplates. Conbextra BB can be used in section thicknesses of 10mm to 100mm. Unit Size: 25kg

A 50mm wide double-sided butyl tape for sealing lap joint and for use in detailing work. Unit Size: 50mm x 30m x 1.5mm

A 125mm corner piece made from polyethylene membrane with a 100mm butyl selvedge for use in conjuction with Proofex L Section.

A cross linked, semi-rigid, closed cell polyethylene sheet material used for forming or filling expansion joints between adjacent in-situ or precast components. Hydrocell XL provides excellent support back to elastomeric sealants and is especially recommended for use in expansion joints in brickwork and in the construction of water retaining and water excluding structures. Unit Size: 15mm x 1000mm x 2000mm

Fosroc Galvafroid zinc rich cold galvanising coating is formulated as an easily applied protection against corrosion on all ferrous metals. Galvafroid has a mid-grey matt finish. Unit Size: 800ml

A fast setting cementitious repair mortar designed for general concrete repairs, in particular for the precast industry. Renderoc Pacth is designed for arris repairs and reprofiling and can be applied overhead from featheredge to 20mm maximum and vertically from featheredge up to 30mm maximum without slump deformation. Unit Size: 25kg

A 125mm corner piece made from polyethylene membrane with a 100mm butyl selvedge for use in conjuction with Proofex L Section.

A rapid setting cementitious waterstopping mortar which is easy to apply to horizontal, vertical or overhead surfaces at a wide range of thickness. Unit Size: 6kg

A reuseable metal sleeve to be used as part of the Proofex EFS range. Unit Size: Each

A high performance free flowing low alkali micro concrete conforming to the requirements of Highways England Specfication for Highways Works and EN1504-3 Structural and Non-structural concrete Class R4. Renderoc LA60 can typically be applied in thicknesses between 25 and 300mm whilst minimising risk of thermal cracking. Unit Size: 25kg bag

An anti-corrosion primer for exposed steel reinforcement, for use with Fosroc concrete repair mortars. Unit Size: 800ml can

An ultra-high performance grout specifically designed for structural grouted connections for wind turbines foundations and oil and gas installations. Suitable for gap depths in the range of 10 to 150mm. Unit Size: 25kg

A cementitious, polymer modified fairing coat, designed for vertical and overhead use to infill honeycombing and voids up to 3mm deep in the surface of concrete which is not trafficked and is subsequently coated. Unit Size: 25kg bag

A cross linked, semi-rigid, closed cell polyethylene sheet material used for forming or filling expansion joints between adjacent in-situ or precast components. Hydrocell XL provides excellent support back to elastomeric sealants and is especially recommended for use in expansion joints in brickwork and in the construction of water retaining and water excluding structures. Unit Size: 10mm x 1000mm x 2000mm

A pre-formed pipe collar with a flat based to simplify pipe penetration details. Available in standard diameters 110mm and 160mm.

A high strength, polymer modified, cementitious repair material which has been specifically engineered for vertical or horizontal use. It can be applied up to 10mm thickness in vertical locations and up to 100mm thickness in horizontal locations in a single application. Unit Size: 25kg