Fosroc Concrete Repair

A low viscosity system for the injection of cracks between 0.3mm and 9mm wide in concrete and masonry, where both sides of the crack can be sealed to prevent resin drainage. Unit Size: 3 ltr pack (2 x 1.5ltr units each consisting of base & hardener)

A high build epoxy coating, non-toxic for application to damp surfaces. Unit Size: 2.5kg packs

A high build epoxy coating, non-toxic for application to damp surfaces. Unit Size: 2.5kg packs

A flexible two-component polymer cementitious coating, used for waterproofing water retaining structures and water excluding structures. Unit Size: 18.2kg bag powder component, 5kg liquid polymer component Available in grey and white.

A flexible two-component polymer cementitious coating, used for waterproofing water retaining structures and water excluding structures. Unit Size: 18.2kg bag powder component, 5kg liquid polymer component Available in grey and white.

A modified acrylic emulsion specially designed for use as a bonding aid and gauging liquid for cementitious systems. Unit Size: 5 ltr

A 100% solids solvent-free epoxy resin containing pigments and fine filler. It is supplied as a two-part material in pre-weighed quantities ready for on-site mixing and use. Coloured components, white base and green hardener, provide visual evidence that adequate mixing is achieved. Unit Size: 2.5kg

A 100% solids solvent-free epoxy resin containing pigments and fine filler. It is supplied as a two-part material in pre-weighed quantities ready for on-site mixing and use. Coloured components, white base and green hardener, provide visual evidence that adequate mixing is achieved. Unit Size: 4.5kg

A modified acrylic emulsion which is specially designed for use as a bonding aid, curing agent and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external application. Unit Size: 5ltr

A two component polyester anchoring grout supplied in pre-measured quantities. The material cures quickly to give consistent, high performance anchorages. It is a pourable grade, with a 25 minute gel time at 20°c for use in vertical down holes where the hole is 8 to 40mm greater in diameter than the bar. Unit Size: 2.5ltr

A two-component epoxy anchoring material, supplied in 3:1 ratio side-by-side cartridges with a static mixer nozzle. When applied it sets and cures to firmly secure a variety of steel fixings into concrete and solid masonry substrates. Unit Size: 385ml

Applicator gun for Lokfix E75 Unit Size: Each

Fosroc Lokfix E55S is a two component vinyl-ester anchoring material, supplied in single component cartridges with a static mixer nozzle. When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates. Unit Size: 300ml

Fosroc Lokfix E35S is a two component polyester anchoring material, supplied in single component cartridges with a static mixer nozzle. When applied it sets and cures rapidly to firmly secure a variety of steel fixings into concrete and masonry substrates. Unit Size: 300ml

A high performance, multi-purpose cementitious protective coating, fairing and levelling mortar for applications from feather edge to 5mm, conforming to the requirements of BS EN 1504-3 Class R4. Unit Size: 20kg powder & 5 ltr liquid

A high strength, polymer modified, cementitious repair material which has been specifically engineered for vertical or horizontal use. It can be applied up to 10mm thickness in vertical locations and up to 100mm thickness in horizontal locations in a single application. Unit Size: 25kg

A two component cementitious slurry material compromising specially selected cementitious powders and liquid polymer additives. The mixed slurry is applied to properly prepared concrete, the specific Renderoc repair material is then compacted into the primer whilst this is still wet. Unit Size: 4kg Part A & 1 ltr Part B, or 20kg Part A & 5 ltrs Part B

A two component cementitious slurry material comprising specially selected cementitious powders and liquid polymer additives. The mixed slurry is applied to properly prepared concrete, the specific Renderoc repair material is then compacted into the primer whilst this is still wet. Unit Size: 20kg Part A & 5 ltrs Part B

A rapid setting mortar which is easy to apply to horizontal, vertical or overhead surfaces at a wide range of thickness. Unit Size: 25kg

A rapid setting cementitious waterstopping mortar which is easy to apply to horizontal, vertical or overhead surfaces at a wide range of thickness. Unit Size: 6kg

A fast setting cementitious repair mortar designed for general concrete repairs, in particular for the precast industry. Renderoc Pacth is designed for arris repairs and reprofiling and can be applied overhead from featheredge to 20mm maximum and vertically from featheredge up to 30mm maximum without slump deformation. Unit Size: 25kg

A high performance free flowing low alkali micro concrete conforming to the requirements of Highways England Specfication for Highways Works and EN1504-3 Structural and Non-structural concrete Class R4. Renderoc LA60 can typically be applied in thicknesses between 25 and 300mm whilst minimising risk of thermal cracking. Unit Size: 25kg bag

A high performance, free flowing low alkali micro concrete conforming to the requirements of BS EN 1504-3 Class R4. Renderoc LA55 is designed for large volume repairs typically in excess of 25mm deep. Unit Size: 25kg bags

A high performance free flowing low alkali micro concrete conforming to the requirements of BS EN 1504-3 Class R4. Renderoc LA is designed for large volume repairs typically in excess of 25mm deep. Unit Size: 25kg

A high strength, high build concrete repair mortar which has been specifically engineered for vertical and overhead repair work. It can be applied in sections up to 40mm thickness in vertical locations and up to 30mm thickness in overhead locations in a single application without the use of formwork. Unit Size: 25kg